Lights Left On Buzzer 83/84 - Revision history

Albell at 04:45, 25 June 2010

2010-06-25T04:45:45Z

Albell at 04:42, 25 June 2010

2010-06-25T04:42:06Z

Rocky Squirrel at 22:41, 24 June 2010

2010-06-24T22:41:31Z

Rocky Squirrel at 22:39, 24 June 2010

2010-06-24T22:39:39Z

Rocky Squirrel at 22:38, 24 June 2010

2010-06-24T22:38:52Z

Rocky Squirrel at 20:24, 24 June 2010

2010-06-24T20:24:05Z

Rocky Squirrel at 20:21, 24 June 2010

2010-06-24T20:21:03Z

Rocky Squirrel at 20:20, 24 June 2010

2010-06-24T20:20:29Z

Rocky Squirrel at 20:19, 24 June 2010

2010-06-24T20:19:38Z

Rocky Squirrel at 20:18, 24 June 2010

2010-06-24T20:18:01Z

← Older revision		Revision as of 04:45, 25 June 2010
Line 243:		Line 243:
	--[[User:Rocky Squirrel\|Rocky Squirrel]] 20:20, 24 June 2010 (UTC)		--[[User:Rocky Squirrel\|Rocky Squirrel]] 20:20, 24 June 2010 (UTC)

		+	<br>

		+	=== 1986 and newer models ===

−	For another way, on 1986 and newer models, see [http://shufti.wordpress.com/2010/05/15/headlight-on-warning-chime-mod/ this procedure].	+	For another way, on 1986 and newer models, see [http://shufti.wordpress.com/2010/05/15/headlight-on-warning-chime-mod/ this procedure].
		+
		+	--[[User:Albell\|Albell]] 04:45, 25 June 2010 (UTC)

@@ Line 199: / Line 199: @@
 The condition for when I wanted the buzzer to sound was when the ignition was off, but the light switch NOT off. This is shown in the green section of the table. Next, I needed to find two fuses: one with power under these conditions, and second with no power under these conditions. If I could find such a pair then I could connect the buzzer between them. As can be seen, Fuses #1 and #2 are powered while Fuses #10, #11, #12 have no power in the green section.&nbsp;
 So I have my candidate fuses.&nbsp;
 === Testing  ===
@@ Line 229: / Line 229: @@
 Reconnect the battery and check for sounding action, in case a crimp has been fumbled.
 Use the double-sided tape to affix the buzzer atop one of the relays.<br>
 === Photos  ===
@@ Line 241: / Line 241: @@
 Note: Mr Squirrel is aware that it is not clear how exactly the buzzer finds a path to ground when Fuse #12 is unpowered. But the buzzer only requires 15mA to operate so something is working.&nbsp;
 --[[User:Rocky Squirrel|Rocky Squirrel]] 20:20, 24 June 2010 (UTC)

@@ Line 7: / Line 7: @@
 === Identifying My Signals  ===
-I wanted to find an easy way to wire a buzzer into the van without cutting wires, which means I was limited to working on the fuse panel. So I hoped to find a pair of fuses that could power a small 12VDC buzzer when the ignition is off but the headlight switch was not.
+I wanted to find an easy way to wire a buzzer into the van without cutting wires, which means I was limited to working on the fuse panel. So I hoped to find a pair of fuses that could power a small 12VDC buzzer when the ignition is off but the headlight switch is not.
 With my trusty voltmeter, I built a "truth table" of fuse voltages, as shown here:<br>
@@ Line 197: / Line 197: @@
 ''Truth Table for my 1984 Westfalia ONLY. Ignition Key is shown in OFF and ON positions, Headlight Switching is shown in four conditions: Main switch OFF (0), Main Switch set to middle, parking light position (1), Main switch set to ON (2) position and beams set to low, and with beams set to hi. Voltages on the fuses measured under all eight combinations, a "0" indicating no volts, a "1" indicating 12 volts. Build your own truth table for your vehicle before proceeding.&nbsp;''
-The condition for when I wanted the buzzer to sound was when the ignition was off, but the light switch NOT off. This is shown in the green section of the table. Next, I needed to find two fuses: one with power under these conditions, and second with no power under these conditions. If I could find such a pair then I could connect the buzzer between them. As can be seen, Fuse #2 is powered while Fuses #10, #11, #12 have no power in the green section.&nbsp;
+The condition for when I wanted the buzzer to sound was when the ignition was off, but the light switch NOT off. This is shown in the green section of the table. Next, I needed to find two fuses: one with power under these conditions, and second with no power under these conditions. If I could find such a pair then I could connect the buzzer between them. As can be seen, Fuses #1 and #2 are powered while Fuses #10, #11, #12 have no power in the green section.&nbsp;
 So I have my candidate fuses.&nbsp;
 === Testing  ===

@@ Line 219: / Line 219: @@
 *Crimping tool.
-Crimp insulated female quick disconnect to both of the buzzer's wires.&nbsp;
+Crimp insulated female quick disconnects to each of the buzzer's wires.&nbsp;
 Disconnect the battery and pull the fuse panel; work it around so &nbsp;the backside is accessible. I had to remove Relay #19 to get to the rear of Fuse #12.&nbsp;

@@ Line 219: / Line 219: @@
 *Crimping tool.
-I started by crimping an insulated female quick disconnect to both of the buzzer's wires.&nbsp;
+Crimp insulated female quick disconnect to both of the buzzer's wires.&nbsp;
-I disconnected the battery again and pulled the fuse panel and worked it around so I could get at the backside. I had to remove Relay #19 to get to the rear of Fuse #12.&nbsp;
+Disconnect the battery and pull the fuse panel; work it around so &nbsp;the backside is accessible. I had to remove Relay #19 to get to the rear of Fuse #12.&nbsp;
-On the rear of Fuse #12, I disconnected the black/yellow wire and installed one of the adapters onto the now-unused tab. I pushed the black/yellow wire back on to one of the two male tabs on the adapter, and pushed the buzzer's black wire onto the other other tab on the adapter.&nbsp;
+On the rear of Fuse #12, I disconnect the black/yellow wire and install one of the adapters onto the now-unused tab. Push the black/yellow wire back on to one of the two male tabs on the adapter, and push the buzzer's black wire onto the other other tab on the adapter.&nbsp;
-On the rear of Fuse #2, I disconnected the gray/red wire, installed the other adapter, pushed the gray/red wire onto one of the two tabs, and pushed the buzzer's red wire onto the other.&nbsp;
+On the rear of Fuse #2, disconnect the gray/red wire, install the other adapter, push the gray/red wire onto one of the two tabs, and push the buzzer's red wire onto the other.&nbsp;
-I reconnected the battery and checked for sounding action, in case I had fumbled a crimp. The buzzer buzzed.
+Reconnect the battery and check for sounding action, in case a crimp has been fumbled.
-Using the double-sided tape, I affixed the buzzer atop one of the relays.<br>
+Use the double-sided tape to affix the buzzer atop one of the relays.<br>
 === Photos  ===

@@ Line 3: / Line 3: @@
 ''This modification has been tested in Mr Squirrel's 1984 Westfalia, Mellow Yellow. Wiring differences between camper versions and standard version of Vanagons as well as changes made to the wiring over the years by Volkswagen and Previous Owners makes it essential that you don't trust any of the information here, and verify your own van's wiring before plunging in.''&nbsp;
-Mr Squirrel is not as smart as he wishes he was and has on more than one occasion found that he forgot to turn off the lights. So he put together this warning buzzer. Here's how it goes:<br>
+Mr Squirrel is not as smart as he wishes he was and has found on more than one occasion that he forgot to turn off the lights. So he put together this warning buzzer. Here's how it goes:<br>
 === Identifying My Signals  ===
@@ Line 197: / Line 197: @@
 ''Truth Table for my 1984 Westfalia ONLY. Ignition Key is shown in OFF and ON positions, Headlight Switching is shown in four conditions: Main switch OFF (0), Main Switch set to middle, parking light position (1), Main switch set to ON (2) position and beams set to low, and with beams set to hi. Voltages on the fuses measured under all eight combinations, a "0" indicating no volts, a "1" indicating 12 volts. Build your own truth table for your vehicle before proceeding.&nbsp;''
-The condition for when I wanted the buzzer to sound was when the ignition was off, but the light switch NOT off. This is shown in the green section of the table. What I needed to find was a fuse with power under these conditions, and another fuse with no power under these conditions. If I could find such a pair then I could connect the buzzer between them. As can be seen, Fuse #2 is powered while Fuses #10, #11, #12 have no power in the green section.&nbsp;
+The condition for when I wanted the buzzer to sound was when the ignition was off, but the light switch NOT off. This is shown in the green section of the table. Next, I needed to find two fuses: one with power under these conditions, and second with no power under these conditions. If I could find such a pair then I could connect the buzzer between them. As can be seen, Fuse #2 is powered while Fuses #10, #11, #12 have no power in the green section.&nbsp;
 So I have my candidate fuses.&nbsp;
@@ Line 215: / Line 215: @@
 *One buzzer. Radio Shack P/N 273-055A. David Beierl suggested this device. It's designed for 12V, and emits an annoying whine, kind of like Paul Simon.
 *Two insulated push-on female quick-disconnect in .250&nbsp;size, for 18-22 gauge wire.&nbsp;
-*Two .250quick-disconnect adapters - single-female, dual-male, like Pico Wiring p/n 1595 as shown here:&nbsp;[http://picowiring.com/pdf/PICO-11.pdf http://picowiring.com/pdf/PICO-11.pdf]
+*Two .250 quick-disconnect adapters: single-female, dual-male, like Pico Wiring p/n 1595 as shown here:&nbsp;[http://picowiring.com/pdf/PICO-11.pdf http://picowiring.com/pdf/PICO-11.pdf]
 *Bit of double-sided sticky tape.&nbsp;
 *Crimping tool.

@@ Line 233: / Line 233: @@
 === Photos  ===
 (Click on images for larger view)
-[[Image:Headlight Buzzer 1984 Westy 1.JPG|left|240px|Buzzer squatting atop unwilling relay. Click on picture for larger image.]][[Image:Headlight_Buzzer_1984_Westy_2.JPG|240px]]<br>
+[[Image:Headlight Buzzer 1984 Westy 1.JPG|left|240px|Buzzer squatting atop unwilling relay. Click on picture for larger image.]][[Image:Headlight Buzzer 1984 Westy 2.JPG|240px]]<br>
-Note: Mr Squirrel is aware that it is not clear how exactly the buzzer finds a path to ground when Fuse #12 is unpowered. But the buzzer only requires 15mA to operate so something is working.&nbsp;
+--[[User:Rocky Squirrel|Rocky Squirrel]] 20:20, 24 June 2010 (UTC)