Delay dim interior lights - Revision history

MariusStrom: Re-adding captions

2010-06-04T02:49:14Z

Re-adding captions

MariusStrom: Merge categories

2010-06-03T17:24:43Z

Merge categories

MariusStrom: Categorize and clean-up

2010-06-02T06:48:22Z

Categorize and clean-up

Albell at 17:36, 1 June 2010

2010-06-01T17:36:38Z

Albell: Created page with ' Installing a delay dim interior light in drivers side. Light is from a late ’80′s early ’90′s golf/jetta carat/wolfsburg models, looks like standard vanagon inter…'

2010-06-01T17:28:17Z

Created page with ' Installing a delay dim interior light in drivers side. Light is from a late ’80′s early ’90′s golf/jetta carat/wolfsburg models, looks like standard vanagon inter…'

New page

 Installing a delay dim interior light in drivers side.

Light is from a late ’80′s early ’90′s golf/jetta carat/wolfsburg models, looks like standard vanagon interior light with some added circuitry, (VW part number, 191947111 “interior light with delayed switch-off”). Get it with the connector, cut the wires on donor about 4 inches long.

Stock drivers side interior light pries out. Cut the wires about 2" from light, or pull off spade connections if you want to connect to new light via male/female spades. Pictures below shows but connecters used.

Very simple splicing, 2 red wires (power) on van to the light’s 2 reds, the 2 brown wires on van (ground) to matching 2, and the brown with white stripe on van (switched ground, door switch) to matching wire. 

Reinstall light. Its about a 6-8 second delay after last door closes.

The bonus is that the delay works on all the lights and all the doors, slider, back hatch, pass. door (if you have door switches on slider and back hatch ). Yup, just by installing that one light at driver’s position.

[[Image:Img 1064.jpg]]

[[Image:Img 1062.jpg]][[Image:Img 1061.jpg]]

@@ Line 11: / Line 11: @@
 The bonus is that the delay works on all the lights and all the doors, slider, back hatch, pass. door (if you have door switches on slider and back hatch). Yup, just by installing that one light at driver’s position.
-[[Image:Img 1064.jpg|thumb|left|200px]]
+[[Image:Img 1064.jpg|thumb|left|200px|View of circuitry]]
-[[Image:Img 1062.jpg|thumb|left|200px]]
+[[Image:Img 1062.jpg|thumb|left|200px|Light]]
-[[Image:Img 1061.jpg|thumb|left|200px]]
+[[Image:Img 1061.jpg|thumb|left|200px|Connections]]
 [[Category:Electrical]]

← Older revision		Revision as of 17:24, 3 June 2010
Line 17:		Line 17:
	[[Image:Img 1061.jpg\|thumb\|left\|200px]]		[[Image:Img 1061.jpg\|thumb\|left\|200px]]

−	[[Category:~~Electronics~~]]	+	[[Category:Electrical]]

@@ Line 1: / Line 1: @@
-&nbsp;Installing a delay dim interior light in drivers side.
+== Installing a delay dim interior light in driver's side  ==
-Light is from a late ’80′s early ’90′s golf/jetta carat/wolfsburg models, looks like standard vanagon interior light with some added circuitry, (VW part number, 191947111&nbsp;“interior light with delayed switch-off”). Get it with the connector, cut the wires on donor about 4 inches long.
+Light is from a late ’80′s early ’90′s Golf/Jetta Carat/Wolfsburg models, looks like standard Vanagon interior light with some additional circuitry, (VW part number, 191947111&nbsp;“interior light with delayed switch-off”). Get it with the connector, cut the wires on the donor about 4 inches long.
-Stock drivers side interior light pries out. Cut the wires about 2" from light.&nbsp;
+Stock driver's side interior light pries out. Cut the wires about 2" from light.
-Very simple splicing, 2 red wires (power) on van to the light’s 2 reds, the 2 brown wires on van (ground) to matching 2, and the brown with white stripe on van (switched ground, door switch) to matching wire.&nbsp;Pictures below show butt connecters used.
+Very simple splicing: 2 red wires (power) on van to the light’s 2 reds, the 2 brown wires on van (ground) to matching 2 on the light, and the brown with white stripe on van (switched ground, door switch) to matching wire. Pictures below show butt connecters used.
-Reinstall light. Its about a 6-8 second delay after last door closes.
+Reinstall light. Its about a 6-8 second delay after the last door closes.
-The bonus is that the delay works on all the lights and all the doors, slider, back hatch, pass. door (if you have door switches on slider and back hatch ). Yup, just by installing that one light at driver’s position.
+The bonus is that the delay works on all the lights and all the doors, slider, back hatch, pass. door (if you have door switches on slider and back hatch). Yup, just by installing that one light at driver’s position.
-[[Image:Img 1064.jpg|thumb|left|200px|view of circuitry]]
+[[Image:Img 1064.jpg|thumb|left|200px]]
-[[Image:Img 1062.jpg|thumb|left|200px|light]]
+[[Image:Img 1062.jpg|thumb|left|200px]]
-[[Image:Img 1061.jpg|thumb|left|200px|connections]]
+[[Image:Img 1061.jpg|thumb|left|200px]]

@@ Line 3: / Line 3: @@
 Light is from a late ’80′s early ’90′s golf/jetta carat/wolfsburg models, looks like standard vanagon interior light with some added circuitry, (VW part number, 191947111&nbsp;“interior light with delayed switch-off”). Get it with the connector, cut the wires on donor about 4 inches long.
-Stock drivers side interior light pries out. Cut the wires about 2" from light, or pull off spade connections if you want to connect to new light via male/female spades. Pictures below shows but connecters used.
+Stock drivers side interior light pries out. Cut the wires about 2" from light.&nbsp;
-Very simple splicing, 2 red wires (power) on van to the light’s 2 reds, the 2 brown wires on van (ground) to matching 2, and the brown with white stripe on van (switched ground, door switch) to matching wire.&nbsp;
+Very simple splicing, 2 red wires (power) on van to the light’s 2 reds, the 2 brown wires on van (ground) to matching 2, and the brown with white stripe on van (switched ground, door switch) to matching wire.&nbsp;Pictures below show butt connecters used.
 Reinstall light. Its about a 6-8 second delay after last door closes.
 The bonus is that the delay works on all the lights and all the doors, slider, back hatch, pass. door (if you have door switches on slider and back hatch ). Yup, just by installing that one light at driver’s position.
-[[Image:Img 1064.jpg]]
+[[Image:Img 1064.jpg|thumb|left|200px|view of circuitry]]
-[[Image:Img 1062.jpg]][[Image:Img 1061.jpg]]
+[[Image:Img 1062.jpg|thumb|left|200px|light]]